Acrel AC Programmable Power Meter Single Phase Ammeter LED Display

• Frequency: 45Hz~65Hz
• Auxiliary Supply: AC/DC 85-265V
• Power Consumption: <5va
• Insulation Resistance: ≥ 100mΩ
• Trademark: Acrel
• Origin: Jiangsu, China
• Model NO.: AMC48-AI

Product Description

General

AMC series AC ammeter&voltmeter, adopting AC sampling technology, can directly measure current and voltage of three phase grid. It can be used for local display, and connecting industrial control device to form measuring control system.

 

Parameters

Communication RS485(Modbus-RTU)   Display LCD display, set multiplying power   Rated U & I:AC current: AC1A, 5A Accuracy Active energy: Class 0.5 Installation:Panel mounted Dimension(L*W*H) Panel size (L×W): 48*48mm Cutout(L×W): 45*45mm Depth (H): 93mm   Consumption Current: Power consumption< 0.5VA; Auxiliary power supply: power consumption≤5VA   Auxiliary power supply:AC 220V

Technical Datasheet

 

Technical Parameter		Value
Input	Rated Value	AC voltage:Single phaseAC 100V,400V Three phaseAC 100V,400V,660V(UL-L,Only 72/ 96) AC current:AC1A,5A; DC voltage:1000V,300V,75mV,10V; DC current: 0-20mA,4-20mA,5A;
	Overload	Voltage: 1.2 times rated value(continuous); 2 times rated value /1 second Current:1.2 times rated value(continuous); 10 times rated value /1 second
	Frequency	45Hz~65Hz
	Power Consumption	Power consumption of each voltage,current input circuit is less than 0.5VA
Accuracy		Class 0.5
Function	Display	LED or LCD
	Communication	RS485,Modbus-RTU protocol;(1 start bit,8 data bit,1 stop bit,no parity) Baud Rate 2400/4800/9600/19200 bps etc.
	Alarm	1 channel passive relay,contact capacity 3A/30VDC,3A/250VAC, Used for high,low,unbalance alarm etc.
	Analog	DC4~20mA,( load <500Ω) (note:Shielded wire is specially selected for the above signal input and output)
	Switching	Input:4 channel or 2 channel dry contact Input,built in power supply Output:2 channel switching output,NO relay contact,capacity:3A/30VDC,3A/250VAC
Auxiliary Supply		AC/DC 85-265V
Power Consumption		<5VA
Insulation resistance		≥ 100MΩ
Power frequency withstand voltage		Between power supply set of terminals and signal input,output set of terminals 2kV/1min (RMS) Between the shell and all set of terminals(except the set of terminals reference voltage less than 40V) AC 4kV
Environment	Temperature	Operation: -10ºC~+55ºCStorage: -25°C ~+70°C
	Humidity	≤95%RH,no condensation,without corrosive gas
	Altitude	≤ 2500m

 

Dimension

Network

 

Installation

 

 

 

FAQ

Q: No display on power?
A: Check whether the supply voltage is within the operating voltage range.


Q: Incorrect reading of voltage,current,electricty,etc?
A: Checking that the voltage/current ratio setting are correct;
     Checking whether the wiring mode setting is consistent with the actual situation;
     Checking whether the voltage transformer and current transformer are in good condition.


Q: Abnormal communication?
A: Check whether the adress,baud rate,check bits in the communication;
     Setting are consistent with the host computer;
     Check whether the RS485 converter is normal;
     Check the connection is corrent if the resistor above 120 ohm is connected in parallel at the communication end.